Antibiotic Sensitivity Test

 


1. Objective

The objective of this test was to determine the sensitivity of bacterial isolates to various antibiotic agents, helping guide effective antimicrobial therapy.

 

2. Principle

The test was based on the inhibition of bacterial growth by antibiotics. The Kirby-Bauer disc diffusion method was used, where antibiotic-impregnated discs were placed on an agar plate inoculated with bacteria. The zone of inhibition around each disc indicated the effectiveness of the antibiotic.

3. Materials

  • Pure bacterial isolate

  • Mueller-Hinton agar plates

  • Antibiotic discs (e.g., ampicillin, ciprofloxacin, ceftriaxone)

  • Sterile swabs 

  • McFarland standard (0.5)

  • Incubator (35–37°C)

  • Ruler or caliper

  • CLSI guideline chart for interpretation

4. Procedure

  1. A standardized bacterial suspension (0.5 McFarland) was prepared.

  2. The suspension was evenly spread onto Mueller-Hinton agar using a sterile swab.

  3. Antibiotic discs were placed on the agar surface using sterile forceps.

  4. The plate was incubated at 35–37°C for 16–18 hours.

  5. The diameter of inhibition zones was measured in millimeters and compared to standard CLSI charts.

5. Result (Example)

AntibioticZone (mm)Interpretation
Ciprofloxacin28Sensitive
Ampicillin12Resistant
Gentamicin20Intermediate
Ceftriaxone30Sensitive

6. Uses

  • Identified effective antibiotics for infection treatment

  • Prevented antibiotic resistance

  • Helped in hospital infection control

  • Guided targeted therapy over empirical treatment

7. Conclusion

The antibiotic sensitivity test was a critical diagnostic tool in clinical microbiology that helped ensure rational and effective use of antibiotics, reducing the risk of treatment failure and resistance development.


Comments

Post a Comment

Popular posts from this blog

Urine Culture

Image
  1. Objective To detect and identify pathogenic bacteria (or fungi) in urine and determine their antibiotic susceptibility , especially in suspected urinary tract infections (UTIs) . 2. Principle Urine is inoculated onto differential and selective media to isolate and identify uro-pathogens such as E. coli , Klebsiella , Proteus , and Enterococcus . A colony count is performed to assess the significance of bacterial growth, and susceptibility testing is carried out using methods like Kirby-Bauer disc diffusion . 3. Materials Sterile midstream urine sample Inoculating loop (1 µL or 10 µL calibrated) Culture media: Cystine Lactose Electrolyte Deficient (CLED) agar MacConkey agar Blood agar Incubator (35–37°C) Antibiotic discs (for sensitivity testing) Mueller-Hinton agar (for disc diffusion) PPE and sterile containers 4. Procedure Mix the urine sample gently. Use a calibrated loop to streak the urine onto culture media plate...
Read more

Coombs Test (Antiglobulin Test), including both the Direct and Indirect versions

Image
🧪 1. Objective The objective of the Coombs test was to detect antibodies (or complement proteins) bound to red blood cells (Direct Coombs) or free antibodies in a patient’s serum that could react with red cells (Indirect Coombs). It was used to diagnose immune-mediated hemolytic anemia, hemolytic disease of the fetus and newborn (HDFN), and for crossmatching in transfusions. 🧪 2. Principle The test relied on the use of Coombs reagent (anti-human globulin, AHG), which binds to human IgG and/or complement (C3d) attached to red cells. In the Direct Coombs test (DAT), it detected in vivo sensitization of RBCs. In the Indirect Coombs test (IAT), it detected antibodies in the serum capable of binding to RBC antigens in vitro. Agglutination after addition of AHG indicated a positive result. 🧪 3. Materials Patient’s red blood cells (for DAT) or serum (for IAT) Screening or panel red cells (for IAT) Anti-human globulin reagent (polyspecific or monospecific: anti-Ig...
Read more

Antiphospholipid Antibody Test (e.g., dRVVT)

Image
  1. Objective: To detect antiphospholipid antibodies in patient plasma, especially in suspected cases of antiphospholipid syndrome, using the Dilute Russell’s Viper Venom Time (dRVVT) test. 2. Principle: The dRVVT measures the time it takes for plasma to clot after the addition of diluted Russell's viper venom, which directly activates factor X. In the presence of antiphospholipid antibodies, especially lupus anticoagulant, the clotting time is prolonged. A confirmatory test with excess phospholipids is used to demonstrate correction. 3. Materials Required: Patient citrated plasma Normal pooled plasma (control) Russell’s viper venom reagent (screening and confirmatory) Calcium chloride Platelet-poor plasma Coagulometer or water bath with stopwatch Test tubes and pipettes 4. Procedure: Collected citrated blood and prepared platelet-poor plasma. Added venom reagent to both patient and control plasma. Added calcium chloride to initiate clottin...
Read more